 |
TD-260T is a high performance digital indicator for a strain gauge type transducer, supporting 5 digit display and comparison function etc.
Complying with TEDS standard (IEEE 1451.4 Class2 paired wire interface)
("TEDS" stands for "Transducer Electronic Data Sheet")
When TEDS type transducer is connected, it can be calibrated automatically like a plug and play device!
TD-260T helps complete the calibration very quickly and accurately and can avoid a human error.
Besides, TD-260T succeeds to the same usability as TD-250T.
It is possible to manually set up Zero Calibration, Span Calibration, High-Low Limit Comparison, Digital/Analog Filter, Motion Detect and Zero Tracking are available, too. |
|
|
|
|
 |
|
| Easy to Calibrate!! TEDS Compliant & Plug and Play |
When TEDS type load cell is connected,
it can be calibrated automatically like a plug and play device! |
|
| Remote sense function available |
| 6 wire input to compensate for cable losses |
|
| Full 5 Digit "99999" display available (negative value up to -19999) |
| Easy-to-see by 7 segment green LED |
|
| Equivalent Input Calibration available |
| It is not necessary to prepare a real load for calibration |
|
| Strain Quantity Direct Read Function available |
| It can be used for diagnosis for a load cell which has suspicion of over-load |
|
| Various Limit Comparison Function |
| Not only "Hi" and "Lo", but also "Hi-Hi" and "Lo-Lo" available |
|
| Various Hold Function available |
| Peak, Bottom, Peak to Peak, Zone (Peak, Bottom, Peak to Peak) |
|
Various Options
|
BCD Data Output, RS-232C Interface,
D/A Converter Voltage or Current output, and NDIS Panel |
|
DIN96 size
|
| It can be installed to the instrument panel of manufacturing equipment |
|
Environmental Approval
|
| CE, RoHS |
|
|
|
|
|
 |
|
| Bridge Excitation Voltage |
DC10V, 2.5V±0%, Current/60mA (Remote sense function available) |
| Max. Input |
±3.2mV/V |
| Equivalent Input |
Calibration Range | 0.3mV/V to 3.2mV/V |
| Accuracy |
less than 0.1%FS |
| Zero Balance Range |
±2.0mV/V |
| Accuracy |
Non-linearlity |
less than 0.01%FS +1Digit
|
| Zero drift |
less than 0.5µV/ deg C |
| Gain drift |
less than 25ppm FS/ deg C |
| Analog to Digital Convert Rates |
100 samples / second |
| Low Pass Filter |
3, 10, 30, 100, 300Hz (-12db/oct) |
| Output Voltage |
Voltage |
2V at 1mV/V
|
| Load Resistance |
2kohm or more |
| TEDS (Transducer Electronic Data Sheet) |
IEEE1451.4 Class 2 mix mode interface
(It is selectable with Remote Sensitivity function) |
| Display |
Character |
7 segment green LED, Character height 14.6mm |
| Indicated Value |
-19999 to 99999 |
| Decimal Point |
Position Selectable |
| Display Rates |
4, 6, 10, 20 times / second |
| Display Item |
Calibration |
Zero / Span (TEDS, Real Load, Equivalent Input) |
| Functions |
Limit : Hi, Lo, Hi-Hi, Lo-Lo, Digital Filter, Analog Filter, Motion Detect, Static Strain, Zero Offset, Hold Mode, etc. |
| Hold Function |
Peak, Bottom, Peak to Peak, Zone (Peak, Bottom, Peak to Peak) |
| External IN/OUT |
IN |
Hold, Judge, Clear, Zero |
| OUT |
Hi-Hi, Hi, OK, Lo, Lo-Lo, Limit Signal, Analog Voltage |
| Power |
AC |
100V to 240V 13W |
DC |
10V to 28V 8W |
| Operating Temperature |
-10 to 40 deg C |
| Storage Temperature |
-40 to 80 deg C |
| Relative Humidity |
less than 85% (non condensing) |
| Safety Standards |
Safety |
EN61010-1, CE |
| EMC |
VCCI (Class A), EN61326 (Class A), EN61000-3-2, EN61000-3-3 |
| Dimension (W x H x D) |
Approx. 96mm x 96mm x 146mm |
| Weight |
Approx. 950g |
|
|
| Figure of dimensions (mm) |
  |
|
|
|
|
|
 |
|
| *Option Installed Model |
| Model Name |
AC Model |
DC Model (Option) |
| BCD Pararel Data Output |
TD-260T AC (BCD) |
TD-260T DC (BCD) |
| RS-232C Serial Interface |
TD-260T AC (232C) |
TD-260T DC (232C) |
| D/A Converter Voltage/Current Output |
TD-260T AC (D/A) |
TD-260T DC (D/A) |
| NDIS Panel (Cannot install this along with the option mentioned above) |
TD-260T AC (NDI) |
TD-260T DC (NDI) |
|
|
|
|
|
|
|
|
;)
;)
