 |
The es8 recorder uses a Compact Flash memory card for recording. A stand-alone operation with the LCD and the key allows you to set, monitor, and record.
By connecting to a PC with a built-in USB interface, you can perform the wave monitor and the recording control.
While simultaneously sampling on all channels, using the 16 bits A/D converter individually equiped in each channel,approximately four hours of continuous recording can be done with an internal dry cell battery., An external battery will extend recording time.
The sampling frequency ranges are 5kHz to 1/60Hz. Combining with various types of sensor amplifiers, a wide range of measurement is possible such as; earthquake, natural phenomenon and stractual vibration, mechanical vibration measurement of the strain measurement, and bio-signal measurement. |
|
|
|
|
 |
|
- Low cost data recorder for vibration measurement and an 8channel AD converter with a USB interface for laboratory use.
- Supported CF Card recording data formats are CSV, and TAFFmat (TEAC standard format consisting with a text header file and a binary data file).
- In addition to the manual operations such as Start or Stop, a various automatic measurement modes are also included such as; Level Trigger (Edge detection), Window Trigger,
Pre/Post Trigger, and interval recording.
- With a built-in comparator output, the recorder can be used to monitor usage by generating an external alarm.
- Operates within the wide range of operating temperatures, -10ºC to 50ºC.
|
|
|
|
|
 |
|
| Number of Channels |
8 channels. Individually ON/OFF selectable. |
| A/D Converter |
16 bits successive approximation type. All channels simultaneously sampled (input filter not included) |
| Input Range/Type |
±2, 5 and 10V / unbalance Impedance: 1Mohms |
| Sampling Frequency |
5KHz to 1/60Hz (same sample frequency applied to all channels)
(5K, 2K, 1K, 500, 200, 100, 50, 20, 10, 5, 2, 1, 1/2, 1/5, 1/10, 1/30, 1/60Hz) |
| Record Mode |
Manual, Interval, Level Trigger (Edge/Window), External Trigger, Pre/Post Trigger |
| Comparator Output |
One relay contact (normally open), Relay rating 40V 0.25A
Manual/Level/Window (Trigger condition set separately from recording setting)
Operation delay from the condition met: less than 300μsec |
| Display |
20 characters x 4 lines Character type LCD with backlight |
| Operation Key |
REC, STANDBY, STOP, MENU, ENTER, ESC, UP, DOWN, RIGHT, LEFT |
| Record Media |
Compact Flash (FAT16) Maximum 2GB |
| Data Format |
Text CSV format or binary TAFFmat format selectable.
The maximum sampling frequency is 50Hz for the CSV format. |
| PC Connection |
USB 2.0 Full speed only. * USB Bus power operation is not available. |
| Clock Calibration |
30 second adjustment |
Operating Temperature
and Humidity |
-10ºC to 50ºC (In use under low temperature, LCD may dew)
10% to 85% (non condensing) |
| Power Supply |
Internal : AA type Nickel Metal-Hydride or 4 Alkaline batteries
External: 8-15V DC 12V
Please use the capacity of more than 0.2A for the DC operation, or the accessory AC adaptor.
|
| Dimension(W×H×D) |
Approx. 150mm×40mm×100mm |
| Weight |
Approx. 400g (internal batteries not included) |
| Accessories |
User Manual, AC adaptor, D-sub 25pin connector, Navi software (for real-time display and control),
AA Type dry cell batteries. |
| Safety Standard |
VCCI Class A |
| Option |
Input cable (D-sub 25 pin -BNC ×8)
Terminal box |
|
|
|
| Figure of dimensions (mm) |
 |
|
|
|
|
|
|
|
;)
